What you'll learn...

"This CMR training program was designed, not to re-invent the wheel or create a 'new standard' but to teach the student on the techniques and methods that have proven to be effective in the mold removal industry. Standards have been established or generally recognized as acceptable and it is the CMR's responsibility to make sure that he consistently pulls his contracts and his employees back to the 'standard'. By doing this, he will remain litigation-free. IICRC 520, EPA, NYC Guidelines, and State regulations have been established for this purpose and it is our job to give the CMR a solid foundation on which he can build a strong company." D. Douglas Hoffman, Author of Mold-Free Construction

Why this is so practical...

"Prior to remediation work, the water source contributing to the mold contamination should be identified and rectified. Isolated remediation areas should be dried prior to or at a minimum upon completion of the remediation work. If heightened levels of relative humidity, or saturated surfaces or structural components still exist when the pre-remediation walk-thrus are conducted, a separate scope of work for drying surfaces should be developed. Drying of structures and surfaces should be completed prior to post remediation clearance." Chuck Hector, CMR Trainer and Owner of Remediation Specialists, NJ

This Certified Mold Remediator class is designed to cover all aspects of training required to understand the general techniques of mold remediation. This class qualifies as 24 hours of training and is, therefore, comprehensive enough for anyone who wants to work in the industry throughout the United States. Some of the subjects covered in this training are:

1. Understand the basic principles of microbial remediation as described and generally accepted as the standards in the industry.
2. Maintain familiarity with the equipment and supplies necessary to conduct a microbial remediation project, as well as, the methods for calibration and operation of such equipment.
3. Appreciate the safety hazards presented by microbial remediation projects, and follow the procedures necessary to protect building occupants and remediation workers from such hazards.
4. Recognize that microbial remediation may bring the Remediator into contact with regulated substances such as lead and asbestos and know what to do with these.
5. Properly address water damage in the indoor environment and understand the proper techniques for correcting such problems.
6. Perform structural remediation by establishing proper containment, engineering controls to prevent cross contamination and to protect worker safety and health.
7. Understand and potentially perform HVAC remediation by employing effective cleaning methods when appropriate.
8. Perform contents remediation by removing and properly disposing of damaged building contents and employing effective cleaning methods when appropriate.
9. Understand the inspection and assessment process and, by knowing these, prepare for post-remediation verification.

What the schedule looks like...

DAY ONE -- The Mold Industry and the Mold Inspection Process

• Definitions of Sanitization and Remediation
• Screening/Testing and Analyzing Lab Reports
• Use of Moisture Meters and Other Testing Equipment
• Developing a Report
• Certified Biocide Applicators Program
• Utilizing Chemical Applications and their limitations

DAY TWO -- Legal Issues, Unfair Business Practices, Mold-Free Techniques

• State Licensing Laws and Legal Concerns
• Business Ethics
• The "Mold-Free" Process of Construction and other Techniques
• Certificates of Sanitization and Warranties
• 30 Steps to a Successful Mold Remediation Project
• Rebuilding to avoid Moisture Problems

DAY THREE -- Establishing Containment, Negative Pressure, and Demolition

• PPE and its value to the Business Owner
• Applications of Approved Anti-Microbials and Equipment
• Utilizing Containment and Negative Pressure
• Face Masks and Respirators
• State Application for Licensing and Insurance Requirements
• The Certification Process and re-Certification
• Q&A with CMR Trainers (Panel Discussion)
• Review Testing process

Who is doing the training...

• D. Douglas Hoffman
  • State of Florida Certified General Contractor
  • State of Florida Certified Plumbing Contractor
  • State of Florida Certified Roofing Contractor
  • Hillsborough County IAQ Consultant
  • CMI, CMA, CMR, CBA, CEE, CIEA
  • Executive Director of NORMI
  • Approved Training Provider
  • Author of Mold-Free Construction
  
  
  
• Arnold Schnabel
  • State of Florida Certified General Contractor
  • CMI, CMA, CMR, CBA
  • Bachelor of Science, Engineering
  • Board of Directors for NORMI
  • IAQ Consultant, owner Environmental Solutions, Inc.
  
  
  
• Chuck Hector
  • Owner of Remediation Specialists, NJ
  • CMA, CMR
  • Senior Trainer for Best Training School
  • Developer of the QST and PSP programs
  
  
  
• Ronnie Wirth
  • State of Louisiana Certified Building Contractor
  • Owner of Elite Homes by Wirth, LA
  • Trainer for Best Training School
  • Administrator of the NORMI Healthier Home Certification
  • National Association of Homebuilder's Officer

What you will receive...

CMRs will be provided with a 4" 3-Ring Binder with the following nine (9) sections to serve as a resource manual for the class and for the remediation process. A list of recommended readings, state regulations, and licensing requirements will be provided by the trainers in their respective segments.

    Section 1 - CMI Inspection Course Materials

    Section 2 - Law & Unfair Business Practices

    Section 3 - OSHA/Grace Systems

    Section 4 - Certificates of Sanitization and Warranties

    Section 5 - Remediation Concepts

    Section 6 - Building Air Quality

    Section 7 - Mold-Free Construction Workbook

    Section 8 - Remediation Specialists Practical Information

    Section 9 - Recommended Products

    (Materials may vary depending on the state in which this class is taught)